dmesg отвечает :
Цитата:
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-486 (Debian 2.6.26-24) () (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 Mon Jun 21 05:12:58 UTC 2010
[ 0.000000] CPU: Vendor unknown, using generic init.
[ 0.000000] CPU: Your system may be unstable.
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] 512MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 131072) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 131072
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 131072
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 125984 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI not present or invalid.
[ 0.000000] ACPI Error (tbxfroot-0218): A valid RSDP was not found [20080321]
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:df000000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: root=/dev/hdc1 ro all_generic_ide quiet
[ 0.000000] No local APIC present or hardware disabled
[ 0.000000] mapped APIC to ffffb000 (01403000)
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 1000.037 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] Memory: 509468k/524288k available (1697k kernel code, 14268k reserved, 746k data, 320k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfffb3000 - 0xfffff000 ( 304 kB)
[ 0.004000] vmalloc : 0xe0800000 - 0xfffb1000 ( 503 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.004000] .init : 0xc0366000 - 0xc03b6000 ( 320 kB)
[ 0.004000] .data : 0xc02a8475 - 0xc0363000 ( 746 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02a8475 (1697 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084631] Calibrating delay using timer specific routine.. 2004.19 BogoMIPS (lpj=4008397)
[ 0.084886] Security Framework initialized
[ 0.084935] SELinux: Disabled at boot.
[ 0.084962] Capability LSM initialized
[ 0.085053] Mount-cache hash table entries: 512
[ 0.085818] Initializing cgroup subsys ns
[ 0.085849] Initializing cgroup subsys cpuacct
[ 0.085868] Initializing cgroup subsys devices
[ 0.086007] CPU: Vortex86 SoC 05/02 stepping 02
[ 0.086051] Checking 'hlt' instruction... OK.
[ 0.111316] Freeing SMP alternatives: 0k freed
[ 0.111340] ACPI: Core revision 20080321
[ 0.111545] ACPI Exception (tbxface-0629): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20080321]
[ 0.111585] ACPI: Unable to load the System Description Tables
[ 0.112559] net_namespace: 652 bytes
[ 0.112587] Booting paravirtualized kernel on bare hardware
[ 0.113922] NET: Registered protocol family 16
[ 0.115809] EISA bus registered
[ 0.116881] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=0
[ 0.116903] PCI: Using configuration type 1 for base access
[ 0.116924] Setting up standard PCI resources
[ 0.125724] ACPI: Interpreter disabled.
[ 0.125748] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.126007] pnp: PnP ACPI: disabled
[ 0.126026] PnPBIOS: Scanning system for PnP BIOS support...
[ 0.126120] PnPBIOS: Found PnP BIOS installation structure at 0xc00f3be0
[ 0.126146] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x45aa, dseg 0xf0000
[ 0.131200] PnPBIOS: 13 nodes reported by PnP BIOS; 13 recorded by driver
[ 0.133309] PCI: Probing PCI hardware
[ 0.133330] PCI: Probing PCI hardware (bus 00)
[ 0.137085] PCI: Using IRQ router default [17f3/6031] at 0000:00:07.0
[ 0.137883] system 00:00: iomem range 0x0-0x9fbff could not be reserved
[ 0.137912] system 00:00: iomem range 0x9fc00-0x9ffff could not be reserved
[ 0.137938] system 00:00: iomem range 0xe4000-0xfffff could not be reserved
[ 0.137964] system 00:00: iomem range 0x100000-0x1fffffff could not be reserved
[ 0.137990] system 00:00: iomem range 0xff000000-0xffffffff could not be reserved
[ 0.138059] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[ 0.138084] system 00:08: ioport range 0xcf8-0xcff could not be reserved
[ 0.138108] system 00:08: ioport range 0xfc00-0xfc0f has been reserved
[ 0.138132] system 00:08: ioport range 0xa00-0xa0f has been reserved
[ 0.138156] system 00:08: ioport range 0xa20-0xa2f has been reserved
[ 0.138180] system 00:08: ioport range 0xa10-0xa1f has been reserved
[ 0.138204] system 00:08: ioport range 0xa30-0xa3f has been reserved
[ 0.138228] system 00:08: ioport range 0xa40-0xa4f has been reserved
[ 0.138252] system 00:08: ioport range 0xa50-0xa5f has been reserved
[ 0.138297] system 00:09: ioport range 0xa60-0xa6f has been reserved
[ 0.138346] system 00:0a: ioport range 0x3f0-0x3f5 has been reserved
[ 0.141538] NET: Registered protocol family 2
[ 0.142040] IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.143331] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.145401] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.146422] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.146441] TCP reno registered
[ 0.146789] NET: Registered protocol family 1
[ 0.147466] checking if image is initramfs... it is
[ 3.151593] Freeing initrd memory: 6077k freed
[ 3.154601] audit: initializing netlink socket (disabled)
[ 3.154671] type=2000 audit(1282217747.152:1): initialized
[ 3.155172] Total HugeTLB memory allocated, 0
[ 3.155539] VFS: Disk quotas dquot_6.5.1
[ 3.155687] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.155896] msgmni has been set to 1007
[ 3.156534] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 3.156562] io scheduler noop registered
[ 3.156578] io scheduler anticipatory registered
[ 3.156594] io scheduler deadline registered
[ 3.156661] io scheduler cfq registered (default)
[ 3.156718] pci 0000:00:03.0: Boot video device
[ 3.432073] isapnp: Scanning for PnP cards...
[ 3.785885] isapnp: No Plug & Play device found
[ 3.803638] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 3.816326] brd: module loaded
[ 3.816963] PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
[ 3.819808] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.819844] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 3.820910] mice: PS/2 mouse device common for all mice
[ 3.821736] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 3.821795] rtc0: alarms up to one day
[ 3.822567] EISA: Probing bus 0 at eisa.0
[ 3.822679] EISA: Detected 0 cards.
[ 3.822696] cpuidle: using governor ladder
[ 3.822712] cpuidle: using governor menu
[ 3.822744] No iBFT detected.
[ 3.825095] TCP cubic registered
[ 3.825116] NET: Registered protocol family 17
[ 3.825151] Using IPI Shortcut mode
[ 3.826048] registered taskstats version 1
[ 3.826521] rtc_cmos 00:04: setting system clock to 2010-08-19 11:35:48 UTC (1282217748)
[ 3.827991] Freeing unused kernel memory: 320k freed
[ 3.844141] Clocksource tsc unstable (delta = 231986063 ns)
[ 3.850227] input: AT Translated Set 2 keyboard as /class/input/input0
[ 4.380290] Uniform Multi-Platform E-IDE driver
[ 4.380328] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 4.385090] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
[ 4.385155] Probing IDE interface ide0...
[ 5.624541] Probing IDE interface ide1...
[ 5.912415] hdc: ELITE PRO CF CARD 8GB, ATA DISK drive
[ 6.584633] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 6.584712] ide1 at 0x170-0x177,0x376 on irq 15
[ 6.891013] thermal: Unknown symbol acpi_processor_set_thermal_limit
[ 9.796954] hdc: max request size: 128KiB
[ 9.796985] hdc: 15662304 sectors (8019 MB) w/1KiB Cache, CHS=15538/16/63
[ 9.797202] hdc: hdc1 hdc2 < hdc5 >
[ 10.980987] SCSI subsystem initialized
[ 11.183757] usbcore: registered new interface driver usbfs
[ 11.183962] usbcore: registered new interface driver hub
[ 11.184250] usbcore: registered new device driver usb
[ 11.203432] ehci_hcd 0000:00:0a.1: EHCI Host Controller
[ 11.203894] ehci_hcd 0000:00:0a.1: new USB bus registered, assigned bus number 1
[ 11.214989] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 11.224622] ehci_hcd 0000:00:0a.1: irq 9, io mem 0xfefbb800
[ 11.237519] ehci_hcd 0000:00:0a.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 11.238029] usb usb1: configuration #1 chosen from 1 choice
[ 11.238304] hub 1-0:1.0: USB hub found
[ 11.238370] hub 1-0:1.0: 2 ports detected
[ 11.341655] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 11.341689] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.341711] usb usb1: Product: EHCI Host Controller
[ 11.341728] usb usb1: Manufacturer: Linux 2.6.26-2-486 ehci_hcd
[ 11.341746] usb usb1: SerialNumber: 0000:00:0a.1
[ 11.341916] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 11.342083] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
[ 11.364720] ehci_hcd 0000:00:0b.1: irq 11, io mem 0xfefbbc00
[ 11.376613] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 11.377101] usb usb2: configuration #1 chosen from 1 choice
[ 11.377326] hub 2-0:1.0: USB hub found
[ 11.377389] hub 2-0:1.0: 2 ports detected
[ 11.481304] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 11.481339] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.481360] usb usb2: Product: EHCI Host Controller
[ 11.481378] usb usb2: Manufacturer: Linux 2.6.26-2-486 ehci_hcd
[ 11.481397] usb usb2: SerialNumber: 0000:00:0b.1
[ 11.483277] ohci_hcd 0000:00:0a.0: OHCI Host Controller
[ 11.483473] ohci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 3
[ 11.483566] ohci_hcd 0000:00:0a.0: irq 5, io mem 0xfefb9000
[ 11.656982] usb usb3: configuration #1 chosen from 1 choice
[ 11.657212] hub 3-0:1.0: USB hub found
[ 11.657289] hub 3-0:1.0: 2 ports detected
[ 11.681506] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 11.750057] libata version 3.00 loaded.
[ 11.761228] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 11.761259] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.761281] usb usb3: Product: OHCI Host Controller
[ 11.761298] usb usb3: Manufacturer: Linux 2.6.26-2-486 ohci_hcd
[ 11.761317] usb usb3: SerialNumber: 0000:00:0a.0
[ 11.761571] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 11.761747] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 4
[ 11.761833] ohci_hcd 0000:00:0b.0: irq 10, io mem 0xfefba000ll
[ 11.813587] usb 1-1: configuration #1 chosen from 1 choice
[ 11.815338] usb 1-1: New USB device found, idVendor=eb1a, idProduct=2861
[ 11.815365] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 11.846944] usb usb4: configuration #1 chosen from 1 choice
[ 11.847160] hub 4-0:1.0: USB hub found
[ 11.847233] hub 4-0:1.0: 2 ports detected
[ 11.949280] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 11.949315] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.949336] usb usb4: Product: OHCI Host Controller
[ 11.949353] usb usb4: Manufacturer: Linux 2.6.26-2-486 ohci_hcd
[ 11.949372] usb usb4: SerialNumber: 0000:00:0b.0
[ 12.528698] usb 3-2: new full speed USB device using ohci_hcd and address 2
[ 12.734103] usb 3-2: configuration #1 chosen from 1 choice
[ 12.738078] usb 3-2: New USB device found, idVendor=0d8c, idProduct=0008
[ 12.738109] usb 3-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 12.738130] usb 3-2: Product: C-Media USB Audio Device
[ 13.040692] usb 4-1: new low speed USB device using ohci_hcd and address 2
[ 13.260070] usb 4-1: configuration #1 chosen from 1 choice
[ 13.262594] usb 4-1: New USB device found, idVendor=05c7, idProduct=0113
[ 13.262625] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 13.262646] usb 4-1: Product: USB MOUSE
[ 13.262675] usb 4-1: Manufacturer: Qtronix Corp
[ 14.684421] usbcore: registered new interface driver hiddev
[ 14.737220] input: C-Media USB Audio Device as /class/input/input1
[ 14.748943] input,hidraw0: USB HID v1.00 Device [C-Media USB Audio Device ] on usb-0000:00:0a.0-2
[ 14.763414] input: Qtronix Corp USB MOUSE as /class/input/input2
[ 14.774370] input,hidraw1: USB HID v1.10 Mouse [Qtronix Corp USB MOUSE] on usb-0000:00:0b.0-1
[ 14.774502] usbcore: registered new interface driver usbhid
[ 14.774527] usbhid: v2.6:USB HID core driver
[ 15.634232] PM: Starting manual resume from disk
[ 15.786804] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 15.786838] EXT3-fs: write access will be enabled during recovery.
[ 98.146240] kjournald starting. Commit interval 5 seconds
[ 98.146333] EXT3-fs: hdc1: orphan cleanup on readonly fs
[ 98.146371] ext3_orphan_cleanup: deleting unreferenced inode 418375
[ 98.146589] ext3_orphan_cleanup: deleting unreferenced inode 418374
[ 98.146660] ext3_orphan_cleanup: deleting unreferenced inode 417182
[ 98.146735] ext3_orphan_cleanup: deleting unreferenced inode 298594
[ 98.146863] ext3_orphan_cleanup: deleting unreferenced inode 298568
[ 98.146937] ext3_orphan_cleanup: deleting unreferenced inode 417157
[ 98.146981] EXT3-fs: hdc1: 6 orphan inodes deleted
[ 98.146999] EXT3-fs: recovery complete.
[ 98.708361] EXT3-fs: mounted filesystem with ordered data mode.
[ 102.839684] udevd version 125 started
[ 120.258230] input: PC Speaker as /class/input/input3
[ 121.037733] Linux video capture interface: v2.00
[ 121.307429] em28xx: New device @ 480 Mbps (eb1a:2861, interface 0, class 0)
[ 121.835291] em28xx #0: chip ID is em2860
[ 121.968179] em28xx #0: board has no eeprom
[ 121.979296] em28xx #0: Identified as Unknown EM2750/28xx video grabber (card=1)
[ 121.998443] em28xx #0: found i2c device @ 0x4a [saa7113h]
[ 122.033040] em28xx #0: Your board has no unique USB ID.
[ 122.033156] em28xx #0: A hint were successfully done, based on i2c devicelist hash.
[ 122.033278] em28xx #0: This method is not 100% failproof.
[ 122.033361] em28xx #0: If the board were missdetected, please email this log to:
[ 122.033467] em28xx #0: V4L Mailing List
[ 122.033563] em28xx #0: Board detected as EM2860/SAA711X Reference Design
[ 122.033658] em28xx #0: Registering snapshot button...
[ 122.034088] input: em28xx snapshot button as /class/input/input4
[ 123.123421] saa7115 0-0025: saa7113 found (1f7113d0e100000) @ 0x4a (em28xx #0)
[ 123.919175] em28xx #0: Config register raw data: 0x10
[ 123.943173] em28xx #0: AC97 vendor ID = 0x414c4720
[ 123.955168] em28xx #0: AC97 features = 0x5980
[ 123.955188] em28xx #0: Unknown AC97 audio processor detected!
[ 124.418134] em28xx #0: v4l2 driver version 0.1.2
[ 125.467456] em28xx #0: V4L2 video device registered as video0
[ 125.467485] em28xx #0: V4L2 VBI device registered as vbi0
[ 125.467567] em28xx audio device (eb1a:2861): interface 1, class 1
[ 125.467711] em28xx audio device (eb1a:2861): interface 2, class 1
[ 125.467935] usbcore: registered new interface driver em28xx
[ 125.467961] em28xx driver loaded
[ 128.904980] usbcore: registered new interface driver snd-usb-audio
[ 134.280662] Adding 377488k swap on /dev/hdc5. Priority:-1 extents:1 across:377488k
[ 134.866647] EXT3 FS on hdc1, internal journal
[ 135.834550] loop: module loaded
[ 162.985674] acpi_cpufreq: Unknown symbol acpi_processor_notify_smm
[ 162.986306] acpi_cpufreq: Unknown symbol acpi_processor_unregister_performance
[ 162.987672] acpi_cpufreq: Unknown symbol acpi_processor_preregister_performance
[ 162.988291] acpi_cpufreq: Unknown symbol acpi_processor_register_performance
[ 166.090003] NET: Registered protocol family 10
[ 166.091929] lo: Disabled Privacy Extensions
[ 167.136659] lp: driver loaded but no devices found
[ 169.660724] ppdev: user-space parallel port driver
[ 174.856616] RPC: Registered udp transport module.
[ 174.856647] RPC: Registered tcp transport module.
[ 175.144209] Installing knfsd (copyright (C) 1996 ).
[ 175.284881] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 175.287807] NFSD: starting 90-second grace period
[ 190.550041] Bluetooth: Core ver 2.11
[ 190.561258] NET: Registered protocol family 31
[ 190.561285] Bluetooth: HCI device and connection manager initialized
[ 190.561307] Bluetooth: HCI socket layer initialized
[ 190.846285] Bluetooth: L2CAP ver 2.9
[ 190.846310] Bluetooth: L2CAP socket layer initialized
[ 190.986834] Bluetooth: RFCOMM socket layer initialized
[ 190.986913] Bluetooth: RFCOMM TTY layer initialized
[ 190.986931] Bluetooth: RFCOMM ver 1.8
[ 208.620250] NET: Registered protocol family 5
[ 218.925734] hdc: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
[ 218.925777] hdc: task_no_data_intr: error=0x04 { DriveStatusError }
[ 218.925801] ide: failed opcode was: 0xef
[ 369.828819] usb 1-1: USB disconnect, address 2
[ 369.829556] em28xx #0: disconnecting em28xx #0 video
[ 369.829579] em28xx #0: Deregistering snapshot button
[ 369.875768] em28xx #0: V4L2 device vbi0 deregistered
[ 369.875932] em28xx #0: V4L2 device video0 deregistered
[ 371.237096] usb 1-1: new high speed USB device using ehci_hcd and address 4
[ 371.370044] usb 1-1: configuration #1 chosen from 1 choice
[ 371.372593] em28xx: New device @ 480 Mbps (eb1a:2861, interface 0, class 0)
[ 371.379151] em28xx #0: chip ID is em2860
[ 371.494646] em28xx #0: board has no eeprom
[ 371.510426] em28xx #0: Identified as Unknown EM2750/28xx video grabber (card=1)
[ 371.526514] em28xx #0: found i2c device @ 0x4a [saa7113h]
[ 371.574386] em28xx #0: Your board has no unique USB ID.
[ 371.574501] em28xx #0: A hint were successfully done, based on i2c devicelist hash.
[ 371.574622] em28xx #0: This method is not 100% failproof.
[ 371.574705] em28xx #0: If the board were missdetected, please email this log to:
[ 371.574811] em28xx #0: V4L Mailing List
[ 371.574906] em28xx #0: Board detected as EM2860/SAA711X Reference Design
[ 371.575001] em28xx #0: Registering snapshot button...
[ 371.575411] input: em28xx snapshot button as /class/input/input5
[ 372.157515] saa7115 0-0025: saa7113 found (1f7113d0e100000) @ 0x4a (em28xx #0)
[ 372.873384] em28xx #0: Config register raw data: 0x10
[ 372.897263] em28xx #0: AC97 vendor ID = 0x414c4720
[ 372.909904] em28xx #0: AC97 features = 0x5980
[ 372.909933] em28xx #0: Unknown AC97 audio processor detected!
[ 373.369576] em28xx #0: v4l2 driver version 0.1.2
[ 374.333757] em28xx #0: V4L2 video device registered as video0
[ 374.333787] em28xx #0: V4L2 VBI device registered as vbi0
[ 374.334061] em28xx audio device (eb1a:2861): interface 1, class 1
[ 374.420154] usb 1-1: New USB device found, idVendor=eb1a, idProduct=2861
[ 374.420188] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
нет, то постил не я хотя у меня тоже стоит debian.
Вход 
Регистрация
FAQ 
Пользователи
